Partios Wholesale catalogue
Mpbs Distributor | Suspension & Steering
Polyurethane suspension sleeve (2,606) · Front track control arm silent block (6) · Suspension sleeve (4) · Rear suspension beam silent block (4) · Drive shaft flexible joint (4) · Rear wishbone silent block (4) · Engine bracket (2) · Wheel suspension track control arm, rear (2) · 5 further part types (6)
2,629 current catalogue lines
About the MPBS range
Mpbs’s range at Partios is suspension & steering, and it is concentrated: 2,606 of the 2,629 lines carried sit under one part type, polyurethane suspension sleeve. Behind it the largest groups are front track control arm silent block (6), suspension sleeve (4), rear suspension beam silent block (4), drive shaft flexible joint (4) and rear wishbone silent block (4). Those six account for most of the catalogue; the remaining 10 lines are spread across 7 further part types, so this is depth in a narrow area rather than broad coverage. That tail includes engine bracket, wheel suspension track control arm, rear and exhaust system hanger. Buyers are typically workshops, suspension specialists, motor factors and exporters; suspension and steering parts are commonly replaced in pairs, so matched availability across an axle is the practical constraint. The 2,629 lines carried give reasonable coverage across common applications.
Catalogue products
Vehicle references are indicative — confirm against the article number.
MPBS Polyurethane suspension sleeve 2200515-00/90SHA
Polyurethane bushing, hardness: 90 Sha, outer diameter: 80mm, length 65mm, quantity per set: 1pcs fits: HONDA ACCORD VII 09.02-05.08
View partMPBS Polyurethane suspension sleeve 2200529-00/80SHA
Polyurethane bushing,
View partMPBS Polyurethane suspension sleeve 2200529-00/90SHA
Polyurethane bushing,
View partMPBS Polyurethane suspension sleeve 2200548-00/80SHA
Polyurethane bushing, hardness: 80 Sha, outer diameter: 74,5mm, length 60mm, quantity per set: 1pcs fits: HONDA ACCORD VII, ACCORD VIII 09.02-06.15
View partMPBS Polyurethane suspension sleeve 2200548-00/90SHA
Polyurethane bushing, hardness: 90 Sha, outer diameter: 74,5mm, length 60mm, quantity per set: 1pcs fits: HONDA ACCORD VII, ACCORD VIII 09.02-06.15
View partMPBS Polyurethane suspension sleeve 2200549-00/80SHA
Polyurethane bushing, hardness: 80 Sha, outer diameter: 38mm, length 56mm, quantity per set: 1pcs fits: HONDA ACCORD VII, ACCORD VIII 09.02-
View partMPBS Polyurethane suspension sleeve 2200549-00/90SHA
Polyurethane bushing, hardness: 90 Sha, outer diameter: 38mm, length 56mm, quantity per set: 1pcs fits: HONDA ACCORD VII, ACCORD VIII 09.02-
View partMPBS Polyurethane suspension sleeve 2200648-00/80SHA
Polyurethane bushing, hardness: 80 Sha, outer diameter: 80mm, length 66mm fits: HONDA ACCORD VIII 06.08-06.15
View partMPBS Polyurethane suspension sleeve 2200648-00/90SHA
Polyurethane bushing, hardness: 90 Sha, outer diameter: 80mm, length 66mm fits: HONDA ACCORD VIII 06.08-06.15
View partMPBS Polyurethane suspension sleeve 2201108-00/80SHA
Front upper Swingarm bushing, hardness: 80 Sha, outer diameter: 34mm, length 40mm, quantity per set: 1pcs fits: HONDA CIVIC IV, CIVIC V, CIVIC VI 09.87-02.01
View partMPBS Polyurethane suspension sleeve 2201108-00/90SHA
Front upper Swingarm bushing, hardness: 90 Sha, outer diameter: 34mm, length 40mm, quantity per set: 1pcs fits: HONDA CIVIC V, CIVIC VI, CRX III 10.91-02.01
View partMPBS Polyurethane suspension sleeve 2201110-00/80SHA
Front lower Swingarm bushing outer, hardness: 80 Sha, outer diameter: 40mm, length 50mm, quantity per set: 1pcs, fits only cast iron track control arms fits: HONDA CIVIC IV, CIVIC V 09.87-05.05
View partMPBS Polyurethane suspension sleeve 2201110-00/90SHA
Front lower Swingarm bushing outer, hardness: 90 Sha, outer diameter: 40mm, length 50mm, quantity per set: 1pcs, fits only cast iron track control arms fits: HONDA CIVIC IV, CIVIC V 09.87-05.05
View partMPBS Polyurethane suspension sleeve 2201111-00/80SHA
Front lower Swingarm bushing (inner), hardness: 80 Sha, outer diameter: 37mm, length 50mm, quantity per set: 1pcs fits: HONDA CIVIC IV, CIVIC V, CIVIC VI, CR-V I, CRX II, CRX III 04.86-02.02
View partMPBS Polyurethane suspension sleeve 2201111-00/90SHA
Polyurethane bushing, hardness: 90 Sha, outer diameter: 37mm, length 50mm fits: HONDA CIVIC IV, CIVIC V, CIVIC VI, CR-V I, CRX II, CRX III, PRELUDE III 04.86-02.02
View partMPBS Polyurethane suspension sleeve 22011121A-00/80SHA
Polyurethane stabilizer bushing, hardness: 80 Sha, outer diameter: 26mm, quantity per set: 1pcs fits: HONDA CIVIC IV, CIVIC V, CIVIC VI, CRX II, CRX III, INTEGRA ROVER 400 II, 45 I 09.87-05.05
View partMPBS Polyurethane suspension sleeve 22011121A-00/90SHA
Polyurethane stabilizer bushing, hardness: 90 Sha, outer diameter: 26mm, quantity per set: 1pcs fits: HONDA CIVIC IV, CIVIC V, CIVIC VI, CRX II, CRX III, INTEGRA ROVER 400 II, 45 I 09.87-05.05
View partMPBS Polyurethane suspension sleeve 22011121B-00/80SHA
Polyurethane stabilizer bushing, hardness: 80 Sha, outer diameter: 26mm, quantity per set: 1pcs fits: HONDA CIVIC IV, CIVIC V, CIVIC VI, CRX II, CRX III, INTEGRA ROVER 400 II, 45 I 09.87-05.05
View partMPBS Polyurethane suspension sleeve 22011121B-00/90SHA
Polyurethane stabilizer bushing, hardness: 90 Sha, outer diameter: 26mm, quantity per set: 1pcs fits: HONDA CIVIC IV, CIVIC V, CIVIC VI, CRX II, CRX III, INTEGRA ROVER 400 II, 45 I 09.87-05.05
View partMPBS Polyurethane suspension sleeve 2201123-00/80SHA
Rear swingarm bushing, hardness: 80 Sha, outer diameter: 80mm, length 159mm, quantity per set: 1pcs fits: HONDA CIVIC IV, CIVIC V, CIVIC VI, CR-V I, CRX II, CRX III ROVER 400 II, 45 I 09.87-05.05
View partMPBS Polyurethane suspension sleeve 2201123-00/90SHA
Polyurethane bushing, hardness: 90 Sha, outer diameter: 80mm, length 159mm fits: HONDA CIVIC IV, CIVIC V, CIVIC VI, CRX II, CRX III 09.87-03.01
View partMPBS Polyurethane suspension sleeve 2201125-00/80SHA
Rear suspension bar bushing, hardness: 80 Sha, outer diameter: 31,3mm, length 39mm, quantity per set: 1pcs fits: HONDA CIVIC IV, CIVIC V, CIVIC VI, CR-V I, CRX II, CRX III, INTEGRA 09.87-05.05
View partMPBS Polyurethane suspension sleeve 2201125-00/90SHA
Rear suspension bar bushing, hardness: 90 Sha, outer diameter: 31,3mm, length 39mm, quantity per set: 1pcs fits: HONDA CIVIC IV, CIVIC V, CIVIC VI, CR-V I, CRX II, CRX III, INTEGRA 09.87-05.05
View partMPBS Polyurethane suspension sleeve 2201126-00/80SHA
Rear suspension bar bushing, hardness: 80 Sha, outer diameter: 35mm, quantity per set: 1pcs fits: HONDA CIVIC IV, CIVIC V, CIVIC VI, CR-V I, CRX II, CRX III, INTEGRA ROVER 400 II, 45 I 09.87-05.05
View partMPBS Polyurethane suspension sleeve 2201126-00/90SHA
Rear suspension bar bushing, hardness: 90 Sha, outer diameter: 35mm, quantity per set: 1pcs fits: HONDA CIVIC IV, CIVIC V, CIVIC VI, CR-V I, CRX II, CRX III, INTEGRA ROVER 400 II, 45 I 09.87-05.05
View partMPBS Polyurethane suspension sleeve 2201129-00/80SHA
Polyurethane stabilizer bushing, hardness: 80 Sha, outer diameter: 35,5mm, quantity per set: 2pcs fits: HONDA CIVIC IV, CRX II 09.87-02.92
View partMPBS Polyurethane suspension sleeve 2201129-00/90SHA
Polyurethane bushing,
View partMPBS Polyurethane suspension sleeve 2201172-00/80SHA
Control rod bushings, hardness: 80 Sha, outer diameter: 50mm, quantity per set: 4pcs fits: HONDA CIVIC IV, CRX II 09.87-02.92
View partMPBS Polyurethane suspension sleeve 2201172-00/90SHA
Polyurethane bushing,
View partMPBS Polyurethane suspension sleeve 2201187-00/80SHA
Gearshift lever stabilizer bushings, hardness: 80 Sha, outer diameter: 46mm, quantity per set: 2pcs fits: HONDA CIVIC III, CIVIC IV, CIVIC V, CIVIC VI, CRX II, CRX III, INTEGRA 10.83-10.01
View partMPBS Polyurethane suspension sleeve 2201187-00/90SHA
Polyurethane bushing,
View partMPBS Polyurethane suspension sleeve 2201201/90SHA
Polyurethane bushing,
View partMPBS Polyurethane suspension sleeve 2201202/80SHA
Polyurethane bushing,
View partMPBS Polyurethane suspension sleeve 2201202/90SHA
Polyurethane bushing,
View partMPBS Polyurethane suspension sleeve 2201203/80SHA
Polyurethane bushing,
View partMPBS Polyurethane suspension sleeve 2201203/90SHA
Polyurethane bushing,
View partMPBS Polyurethane suspension sleeve 2201207-00/80SHA
Front lower Swingarm bushing (rear), hardness: 80 Sha, outer diameter: 55mm, quantity per set: 2pcs fits: HONDA CIVIC V, CIVIC VI, CRX II, INTEGRA ROVER 400 II 10.87-10.01
View partMPBS Polyurethane suspension sleeve 2201207-00/90SHA
Front lower Swingarm bushing (rear), hardness: 90 Sha, outer diameter: 55mm, quantity per set: 2pcs fits: HONDA CIVIC V, CIVIC VI, CRX II, INTEGRA ROVER 400 II 10.87-10.01
View partMPBS Polyurethane suspension sleeve 2201213-00/80SHA
Polyurethane bushing,
View partMPBS Polyurethane suspension sleeve 2201213-00/80SHA/12
Front lower Swingarm bushing (inner) 12mm, hardness: 80 Sha, outer diameter: 37,5mm, length 51mm, quantity per set: 2pcs fits: HONDA CIVIC V, CIVIC VI, CR-V I, CRX III ROVER 400 II 10.91-02.02
View partMPBS Polyurethane suspension sleeve 2201213-00/80SHA/14
Front lower Swingarm bushing (inner) 14mm, hardness: 80 Sha, outer diameter: 37,5mm, quantity per set: 2pcs fits: HONDA CIVIC V, CIVIC VI, CR-V I, CRX III ROVER 400 II, 45 I 10.91-05.05
View partMPBS Polyurethane suspension sleeve 2201213-00/90SHA
Polyurethane bushing,
View partMPBS Polyurethane suspension sleeve 2201213-00/90SHA/12
Front lower Swingarm bushing (inner) 12mm, hardness: 90 Sha, outer diameter: 37,5mm, length 51mm, quantity per set: 2pcs fits: HONDA CIVIC V, CIVIC VI, CR-V I, CRX III ROVER 400 II 10.91-02.02
View partMPBS Polyurethane suspension sleeve 2201220-00/80SHA
Rear lower Swingarm bushing (central), hardness: 80 Sha, outer diameter: 46mm, quantity per set: 1pcs fits: HONDA CIVIC IV, CIVIC V, CIVIC VI, CRX II, CRX III, INTEGRA 09.87-10.01
View partMPBS Polyurethane suspension sleeve 2201220-00/90SHA
Rear lower Swingarm bushing (central), hardness: 90 Sha, outer diameter: 46mm, quantity per set: 1pcs fits: HONDA CIVIC IV, CIVIC V, CIVIC VI, CRX II, CRX III, INTEGRA 09.87-10.01
View partMPBS Polyurethane suspension sleeve 2201224-00/80SHA
Rear suspension front bar bushing, hardness: 80 Sha, outer diameter: 30,4mm, length 29mm, quantity per set: 1pcs fits: HONDA CIVIC IV, CIVIC V, CIVIC VI, CR-V I, CRX II, CRX III, INTEGRA 09.87-05.05
View partMPBS Polyurethane suspension sleeve 2201224-00/90SHA
Rear suspension front bar bushing, hardness: 90 Sha, outer diameter: 30,4mm, length 29mm, quantity per set: 1pcs fits: HONDA CIVIC IV, CIVIC V, CIVIC VI, CR-V I, CRX II, CRX III, INTEGRA 09.87-05.05
View partMPBS Polyurethane suspension sleeve 2201229-00/80SHA
Polyurethane bushing,
View partBuying with Partios
Buying MPBS parts through Partios
Are these genuine MPBS parts?
- Yes. Every MPBS line here is sourced through Partios's ISO 9001:2015-certified European distribution network.
Can you source MPBS parts that aren't showing in stock?
- Yes. Partios runs a prepayment-only, manufacturer-order model, so we can place a manufacturer order for MPBS lines that aren't currently available.
Do you supply MPBS parts for export?
- Yes. We serve motor factors, exporters and resellers. Export orders are handled the same way as UK trade orders.
How do I get trade pricing on MPBS parts?
- Apply for a Partios Wholesale trade account to see trade pricing and availability.
What lead time should I expect on a MPBS order?
- It depends on the line. Stocked MPBS items are dispatched within 24 hours of payment for parcel orders, or up to 48 hours for pallet orders depending on size. For lines placed as a manufacturer order, we confirm the lead time with the manufacturer before the order goes in, so you know the timescale before you pay.
Is there a minimum order quantity for MPBS parts?
- No. There's no minimum order value or quantity on a Partios trade account. Some MPBS lines are supplied in manufacturer pack sizes, which are shown on the product listing.
No registration needed
See what we can source
Upload your parts list and we’ll match it against the full catalogue. Add up to 50 rows, with no account needed.
Try the Parts FinderReady to see trade pricing and availability? Apply for a Partios Wholesale account.
Apply for a trade account