Partios Wholesale catalogue

Mpbs Distributor | Suspension & Steering

Polyurethane suspension sleeve (2,606) · Front track control arm silent block (6) · Suspension sleeve (4) · Rear suspension beam silent block (4) · Drive shaft flexible joint (4) · Rear wishbone silent block (4) · Engine bracket (2) · Wheel suspension track control arm, rear (2) · 5 further part types (6)

2,629 current catalogue lines

About the MPBS range

Mpbs’s range at Partios is suspension & steering, and it is concentrated: 2,606 of the 2,629 lines carried sit under one part type, polyurethane suspension sleeve. Behind it the largest groups are front track control arm silent block (6), suspension sleeve (4), rear suspension beam silent block (4), drive shaft flexible joint (4) and rear wishbone silent block (4). Those six account for most of the catalogue; the remaining 10 lines are spread across 7 further part types, so this is depth in a narrow area rather than broad coverage. That tail includes engine bracket, wheel suspension track control arm, rear and exhaust system hanger. Buyers are typically workshops, suspension specialists, motor factors and exporters; suspension and steering parts are commonly replaced in pairs, so matched availability across an axle is the practical constraint. The 2,629 lines carried give reasonable coverage across common applications.

Catalogue products

Vehicle references are indicative — confirm against the article number.

MPBS Polyurethane suspension sleeve 1600551-00/90SHA

Polyurethane bushing,

View part

MPBS Polyurethane suspension sleeve 1600553-00/80SHA

Rear beam bushing, hardness: 80 Sha, outer diameter: 49,3mm, length 74mm, quantity per set: 1pcs fits: DAEWOO ESPERO, LACETTI, LANOS, NEXIA OPEL KADETT E, VECTRA A 09.84-

View part

MPBS Polyurethane suspension sleeve 1600553-00/90SHA

Polyurethane bushing, hardness: 90 Sha, outer diameter: 49,3mm, length 74mm fits: DAEWOO ESPERO, LACETTI, LANOS, NEXIA OPEL ASCONA C, KADETT D, KADETT E, KADETT E COMBO, VECTRA A 08.79-

View part

MPBS Polyurethane suspension sleeve 1601048-00/80SHA

Front Swingarm bushing, hardness: 80 Sha, outer diameter: 56mm, quantity per set: 1pcs fits: DAEWOO NUBIRA 05.97-

View part

MPBS Polyurethane suspension sleeve 1601048-00/90SHA

Polyurethane bushing,

View part

MPBS Polyurethane suspension sleeve 1601049-00/80SHA

Front Swingarm bushing (rear), hardness: 80 Sha, outer diameter: 59,5mm, quantity per set: 1pcs fits: DAEWOO NUBIRA 05.97-

View part

MPBS Polyurethane suspension sleeve 1601049-00/90SHA

Polyurethane bushing,

View part

MPBS Polyurethane suspension sleeve 1800109-00/80SHA

Polyurethane bushing, hardness: 80 Sha, outer diameter: 73mm, length 77mm fits: CHRYSLER 300C DODGE CHALLENGER 09.07-

View part

MPBS Polyurethane suspension sleeve 1800109-00/90SHA

Polyurethane bushing, hardness: 90 Sha, outer diameter: 73mm, length 77mm fits: CHRYSLER 300C DODGE CHALLENGER 09.07-

View part

MPBS Polyurethane suspension sleeve 1800112-00/80SHA

Polyurethane front Swingarm bushing, hardness: 80 Sha, outer diameter: 48,6mm, length 70mm, quantity per set: 1pcs fits: CHRYSLER 300C DODGE CHALLENGER, CHARGER LANCIA THEMA 09.07-

View part

MPBS Polyurethane suspension sleeve 1800112-00/90SHA

Polyurethane front Swingarm bushing, hardness: 90 Sha, outer diameter: 48,6mm, length 70mm, quantity per set: 1pcs fits: CHRYSLER 300C DODGE CHALLENGER, CHARGER LANCIA THEMA 09.07-

View part

MPBS Polyurethane suspension sleeve 1800129-00/80SHA

Polyurethane bushing,

View part

MPBS Polyurethane suspension sleeve 1800129-00/80SHA/25

Polyurethane stabilizer bushing, hardness: 80 Sha, outer diameter: 40mm, quantity per set: 1pcs fits: CHRYSLER 300C DODGE CHARGER, MAGNUM 09.04-11.12

View part

MPBS Polyurethane suspension sleeve 1800129-00/80SHA/27

Polyurethane stabilizer bushing, hardness: 80 Sha, quantity per set: 1pcs fits: CHRYSLER 300C DODGE CHARGER, MAGNUM 09.04-11.12

View part

MPBS Polyurethane suspension sleeve 1800129-00/80SHA/29

Polyurethane stabilizer bushing, hardness: 80 Sha, outer diameter: 40mm, quantity per set: 1pcs fits: CHRYSLER 300C DODGE CHARGER, MAGNUM 09.04-11.12

View part

MPBS Polyurethane suspension sleeve 1800129-00/80SHA/30

Polyurethane stabilizer bushing, hardness: 80 Sha, outer diameter: 40mm, quantity per set: 1pcs fits: CHRYSLER 300C DODGE CHARGER, MAGNUM 09.04-11.12

View part

MPBS Polyurethane suspension sleeve 1800129-00/80SHA/32

Polyurethane stabilizer bushing, hardness: 80 Sha, outer diameter: 40mm, quantity per set: 1pcs fits: CHRYSLER 300C DODGE CHARGER, MAGNUM 09.04-11.12

View part

MPBS Polyurethane suspension sleeve 1800129-00/90SHA

Polyurethane bushing,

View part

MPBS Polyurethane suspension sleeve 1800248-00/80SHA

Polyurethane bushing, hardness: 80 Sha, outer diameter: 37,8mm, length 60mm fits: CITROEN C4 AIRCROSS, C-CROSSER DODGE CALIBER JEEP COMPASS, PATRIOT MITSUBISHI ASX, COLT VI, LANCER VIII 06.04-

View part

MPBS Polyurethane suspension sleeve 1800248-00/90SHA

Polyurethane bushing, hardness: 90 Sha, outer diameter: 37,8mm, length 60mm fits: CITROEN C4 AIRCROSS, C-CROSSER DODGE CALIBER JEEP COMPASS, PATRIOT MITSUBISHI ASX, COLT VI, LANCER VIII 06.04-

View part

MPBS Polyurethane suspension sleeve 1800249-00/80SHA

Polyurethane bushing, hardness: 80 Sha, outer diameter: 60mm, length 54mm fits: CITROEN C4 AIRCROSS, C-CROSSER DODGE CALIBER MITSUBISHI LANCER VIII, OUTLANDER II, OUTLANDER III 06.06-

View part

MPBS Polyurethane suspension sleeve 1800249-00/90SHA

Polyurethane bushing, hardness: 90 Sha, outer diameter: 60mm, length 54mm fits: CITROEN C4 AIRCROSS, C-CROSSER DODGE CALIBER MITSUBISHI LANCER VIII, OUTLANDER II, OUTLANDER III 06.06-

View part

MPBS Polyurethane suspension sleeve 2000348-00/80SHA

Polyurethane suspension sleeve, hardness: 80 Sha, outer diameter: 31,3mm, length 52,5mm, quantity per set: 1pcs fits: ABARTH 500 / 595 / 695, 500C / 595C / 695C FIAT 500, 500 C, GRANDE PUNTO 09.99-

View part

MPBS Polyurethane suspension sleeve 2000348-00/90SHA

Polyurethane suspension sleeve, hardness: 90 Sha, outer diameter: 31,3mm, length 52,5mm, quantity per set: 1pcs fits: ABARTH 500 / 595 / 695, 500C / 595C / 695C FIAT 500, 500 C, GRANDE PUNTO 09.99-

View part

MPBS Polyurethane suspension sleeve 2000349-00/80SHA

Polyurethane bushing, hardness: 80 Sha, outer diameter: 60mm, length 52mm, quantity per set: 1pcs fits: ABARTH 500C / 595C / 695C FIAT 500, 500 C FORD KA 07.07-

View part

MPBS Polyurethane suspension sleeve 2000349-00/90SHA

Polyurethane bushing, hardness: 90 Sha, outer diameter: 60mm, length 52mm, quantity per set: 1pcs fits: ABARTH 500C / 595C / 695C FIAT 500, 500 C FORD KA 07.07-

View part

MPBS Polyurethane suspension sleeve 2000353-00/80SHA

Polyurethane rear beam bushing, hardness: 80 Sha, outer diameter: 52mm, length 52mm, quantity per set: 1pcs fits: ABARTH 500 / 595 / 695, 500C / 595C / 695C FIAT 500, 500 C, PANDA, PUNTO 09.99-

View part

MPBS Polyurethane suspension sleeve 2000353-00/90SHA

Polyurethane rear beam bushing, hardness: 90 Sha, outer diameter: 52mm, length 52mm, quantity per set: 1pcs fits: ABARTH 500 / 595 / 695, 500C / 595C / 695C FIAT 500, 500 C, PANDA, PUNTO 09.99-

View part

MPBS Polyurethane suspension sleeve 2001048-00/80SHA

Front Swingarm bushing, hardness: 80 Sha, outer diameter: 40mm, quantity per set: 1pcs fits: FIAT BARCHETTA, CINQUECENTO, PUNTO, SEICENTO / 600, UNO LANCIA Y 03.83-01.10

View part

MPBS Polyurethane suspension sleeve 2001048-00/90SHA

Polyurethane bushing,

View part

MPBS Polyurethane suspension sleeve 2001602/90SHA

Polyurethane bushing,

View part

MPBS Polyurethane suspension sleeve 2001629-00/80SHA

Polyurethane bushing,

View part

MPBS Polyurethane suspension sleeve 2001629-00/80SHA/16

Polyurethane stabilizer bushing, hardness: 80 Sha, outer diameter: 62mm, quantity per set: 1pcs fits: CITROEN JUMPER I FIAT DUCATO PEUGEOT BOXER 02.94-04.02

View part

MPBS Polyurethane suspension sleeve 2001629-00/80SHA/24

Polyurethane stabilizer bushing, hardness: 80 Sha, outer diameter: 62mm, quantity per set: 1pcs fits: CITROEN JUMPER I FIAT DUCATO PEUGEOT BOXER 02.94-04.02

View part

MPBS Polyurethane suspension sleeve 2001629-00/90SHA

Polyurethane bushing,

View part

MPBS Polyurethane suspension sleeve 2001631-00/80SHA

Polyurethane stabilizer bushing, hardness: 80 Sha, outer diameter: 37mm, quantity per set: 1pcs fits: CITROEN JUMPER I, JUMPER II FIAT DUCATO PEUGEOT BOXER 02.94-

View part

MPBS Polyurethane suspension sleeve 2001631-00/90SHA

Polyurethane bushing,

View part

MPBS Polyurethane suspension sleeve 2001648-00/80SHA

Front Swingarm bushing, hardness: 80 Sha, outer diameter: 46mm, length 65mm, quantity per set: 1pcs fits: CITROEN JUMPER I, JUMPER II FIAT DUCATO PEUGEOT BOXER 03.89-

View part

MPBS Polyurethane suspension sleeve 2001648-00/90SHA

Polyurethane bushing, hardness: 90 Sha, outer diameter: 46mm, length 65mm fits: CITROEN JUMPER I, JUMPER II FIAT DUCATO PEUGEOT BOXER 03.94-

View part

MPBS Polyurethane suspension sleeve 2001649-00/80SHA

Front Swingarm bushing (rear), hardness: 80 Sha, outer diameter: 61mm, length 64mm, quantity per set: 1pcs, cartridge fits: CITROEN JUMPER I, JUMPER II FIAT DUCATO PEUGEOT BOXER 03.89-

View part

MPBS Polyurethane suspension sleeve 2001649-00/90SHA

Polyurethane bushing, hardness: 90 Sha, outer diameter: 61mm, length 64mm fits: CITROEN JUMPER I, JUMPER II FIAT DUCATO PEUGEOT BOXER 03.89-

View part

MPBS Polyurethane suspension sleeve 2001848-00/80SHA

Polyurethane bushing, hardness: 80 Sha, outer diameter: 34,6mm, length 60mm fits: DODGE JOURNEY FIAT FREEMONT 06.08-

View part

MPBS Polyurethane suspension sleeve 2001848-00/90SHA

Polyurethane bushing, hardness: 90 Sha, outer diameter: 34,6mm, length 60mm fits: DODGE JOURNEY FIAT FREEMONT 06.08-

View part

MPBS Polyurethane suspension sleeve 2001849-00/80SHA

Polyurethane suspension sleeve,

View part

MPBS Polyurethane suspension sleeve 2001849-00/90SHA

Polyurethane bushing,

View part

MPBS Polyurethane suspension sleeve 2002629-00/80SHA

Polyurethane bushing,

View part

MPBS Polyurethane suspension sleeve 2002629-00/90SHA

Polyurethane bushing,

View part

MPBS Polyurethane suspension sleeve 2002662-00/80SHA

Rear Swingarm bushing, hardness: 80 Sha, outer diameter: 42,8mm, length 69mm, quantity per set: 1pcs fits: FIAT PANDA 10.04-

View part

Buying with Partios

Buying MPBS parts through Partios

Are these genuine MPBS parts?

Yes. Every MPBS line here is sourced through Partios's ISO 9001:2015-certified European distribution network.

Can you source MPBS parts that aren't showing in stock?

Yes. Partios runs a prepayment-only, manufacturer-order model, so we can place a manufacturer order for MPBS lines that aren't currently available.

Do you supply MPBS parts for export?

Yes. We serve motor factors, exporters and resellers. Export orders are handled the same way as UK trade orders.

How do I get trade pricing on MPBS parts?

Apply for a Partios Wholesale trade account to see trade pricing and availability.

What lead time should I expect on a MPBS order?

It depends on the line. Stocked MPBS items are dispatched within 24 hours of payment for parcel orders, or up to 48 hours for pallet orders depending on size. For lines placed as a manufacturer order, we confirm the lead time with the manufacturer before the order goes in, so you know the timescale before you pay.

Is there a minimum order quantity for MPBS parts?

No. There's no minimum order value or quantity on a Partios trade account. Some MPBS lines are supplied in manufacturer pack sizes, which are shown on the product listing.

No registration needed

See what we can source

Upload your parts list and we’ll match it against the full catalogue. Add up to 50 rows, with no account needed.

Try the Parts Finder

Ready to see trade pricing and availability? Apply for a Partios Wholesale account.

Apply for a trade account